Floor Tiles Skirting

Thin Porcelain tiles skirting, Gaza 2019

Floor tile skirting is a short wall tile to protect wall from water and to give the walls a nice finishing. The main function of floor tile skirt is to protect the wall from water during floor cleaning. Furniture against the walls will scratch and damage it, tile skirting keep a small distance between wall and furniture. Also tile skirting keep a nice appearance of the connection between tiles and walls. Floor tiles skirting can be made from different materials according to the space function.

skirt is protect the wall from furniture scratching, Gaza 2020
skirt is protect the wall from furniture scratching, Gaza 2020

Tile Skirting Height

Since tile skirting function is to protect the wall from water, several centimeters height are enough. The tiles skirting nice height is 7 cm, I have tried shorter and higher skirt but wasn’t nice as 7 cm in height. Keep in mind that for some special cases, like when the wall has marble cladding one or two centimeters are enough. Select skirting material with low water absorbing to protect marble from water. Select a black granite skirting it will look as a nice shadow line detail.

For tile cladding wall there is no need to install tile skirting. Another special case when there is a wall in less than 15 cm height, like what is used for handrail balcony or curtain wall detail. I prefer to avoid few cm painting wall over the skirting, therefore skirting could be higher or from the same material as sill to appear as a block of marble.

Balcony with low parapet height that need emperador sill full height
Balcony with low parapet height that need emperador sill full height. Gaza Alhelou petrol station 2018

Skirting Cutting Problem

Many companies produce tile skirting in a certain size, these skirts have a straight edges.  Other times, craftsmen cut tiles in certain heights to make the tile’s skirting. There are several methods to cut a porcelain or ceramic tiles either by manual tile cutter, grinder or a saw machine. Cutting tiles using manual tile cutter or grinder won’t have a straight edges. Craftsman will install bad cut edge at the bottom, to avoid it appear to the human eye. Then cement grout used to fill the bad cut edge connection. This cut method can be used if there is much tile pieces that have at least one straight edge. The best tile cut method is saw machine to have straight edges. Not all tiles contractors have in-site saw machine, therefore sometimes they send it to marble workshop to cut them.

skirting cutting problems, show that low edge has bad cut and filled with cement grout that has problems too. Gaza 2020
skirting cutting problems, show that low edge has bad cut and filled with cement grout that has problems too. Gaza 2020

Skirting Round Edges

At the British International School in Gaza project, it required a recognition from the UK. One of the main requirements to get the recognition was student safety, therefore they asked to round skirting edges. The marble flooring and skirting disassembled, then send them to marble factory to round the top edge. Full-body porcelain can round it edge, while full-color porcelain the round edge will have similar color to the edge and won’t look nice. However, can’t round ceramic or veneer tiles because the bisque layer is weak and have a different color.

Skirting round edge from Omani marble, Gaza 2016
Skirting round edge from Omani marble, Gaza 2016
Marble skirt in lathe profile for wall wood cladding
Marble skirt in lathe profile for wall wood cladding, Gaza 2011

Skirting Corners

It’s important to notice that skirting require a 45 degree cut as shown in the following photo. It can’t install over each other to avoid tiles bisque layer to appear. Half on half and other detailed connection doesn’t suite the skirting scale. Also 45 degree corner connection suite when the skirt has a top round edge.

Granite round edge skirting and 45 degree corners, Gaza 2020
Granite round edge skirting and 45 degree corners, Gaza 2020

Plaster Paint  and Tile Skirting Details

As tile skirting role to have a nice wall floor appearance, the wall-skirt detail is important. Most walls have plaster and painting finish and sometimes a wallpaper finish is used. 

For plaster craftsmen like to end their work 15 cm from the top of concrete. 10 cm is the finish floor level, then tile skirt require 7 cm. This means tiles craftsman have two choices either to lay skirting tiles over plaster works or to remove the plaster then lay the skirt. I prefer to remove the plaster then to lay tile skirt to have less thickness skirt. Another finish alternative, when plaster craftsman leave 20 cm from the top of concrete instead of 15 cm. This way they need to finish the 3 cm plaster after the tiles work finish and before tile joint grout begins. 

For painting works, the most important to make a sharp edge between painting and tile skirt, and it’s better to make a round edge to have a nice finish. Also for wallpaper it’s important to know where to end the wallpaper.

Thin Porcelain tiles skirting, Gaza 2019
Thin Porcelain tiles skirting, Gaza 2019
Thick Porcelain tiles skirting that have over lap bad connection filled with cement grout, Gaza 2019
Thick Porcelain tiles skirting that have over lap bad connection filled with cement grout, Gaza 2019

Tiles Expansion Joint

For high temperature countries like Arab Gulf, tiles expansion joint is important. In outdoor and large spaces expansion joint can be installed each 4 meters in both directions. Another expansion joint at room boundaries and in the connection between wall and floor. A centimeter that doesn’t have either tiles or a mortar, then it’s filled with rubber material like SikaFlex or other products. Then the tiles skirt will cover the expansion joint and won’t appear for the human eyes.

Tiles Skirting Connection with Doors

The connection between door and tiles skirting is a sensitive detail. Where door frame install after tiles works and sometimes after the painting works to keep it clean. So site engineering has to give the tiles craftsman where the tile skirting ends. So when the door frame installed they have a nice finish together. Sometimes interior designers make a door frame base to avoid bad connection with tile skirt.

Bad skirting connection with door. Gaza 2020
Bad skirting connection with door. Gaza 2020
How to make curved walls skirting ?

Well, tiles and natural stone materials can’t bend according to the wall curve. Therefore the best solution is to divide the skirt into smaller width size according to the wall curvature. Dividing the skirt width will give a not bad solution that will have a bad appearance.Curved wall skirt using small width species, Gaza 2016

Skirt mortar problem, notice that the tile that doesn’t fill with mortar have echo sound. Gaza 2020

Everything you need to know about Tiles Grout

Grout is tiles joint – small space – between tiles, this space function is to allow the craftsmen to align tiles together. Typically spaces between tiles range from 2 to 4 mm and it measured by plastic grout spacers.

The size of tiles joints can affect the tiles style either modern or classic. For modern appearance usually we recommend arrangement tiles directly with no space. This fit laser cut tiles case, where tiles are well trimmed at 90 degrees angles. On the other hand, saw cutting tiles will have classic appearance. Saw cutting tiles are cheaper than laser cutting tiles, but during manufacturing it could have a difference in tiles size. This could appear clearly by eyes therefore it’s better to use large tiles joint about 7 mm wide. However in classic appearance tiles it more beautiful to leave a large grout space, but be aware to buy a good brand ground to avoid color changing.

Grout function is to align tiles together and it’s not expansion joints, because it could fill by cement grout or in marble tiles cases could fill with epoxy or marble adhesive. Both fillers type could be colored to appear in harmony or in contrast with tiles. 

tiles grout important, and what to fill it. The photo is for a Creama nova marble, Gaza 2019

As expansion joint we recommended to leave around a cm between tiles and walls. The expansion joint will cover by tiles’ skirting. Expansion joints need to be clear from sand and mortar, then to fill with highly stretchable material like Sikaflex. Then it covers with tiles skirting.There is a special accessory for tiles expansion joints where it installed outdoors in high temperature countries.

According to ISO standards 13007, where grout classified according to materials to resin grout RG and cement grout CG. The cement grout classify to CG1 and CG2, of course CG2 is better. You can search about Iso standards 13007 for more information. Notice that there are few other factors affect grout quality. For example, the tile joint has to be clear from sand or dust, so the grout find a place it self. 

Cleaning Tiles Grout

Many people suffer from tile grout cleaning, especially floor cement grout. For cement grout, where cement has pores that could collect dust and dirt. Then the cement grout will become darker and look old. There are some chemical products that clean cement grout like Grout Cleaner from Fila. It will clean the cement pour from dust and dirty then partly close those pour. Designer sometimes use dark color cement grout, in order to protect it from color difference. Compared to epoxy or using marble adhesive as tiles grout, where it has less pour that won’t collect dust and dirt. The epoxy and tile adhesive grout is using only in indoor where sun will fragment it, making creaking and disassembled with walking friction.

FAQs

Can i use Portland cement as cement grout?

Yes, cement grout is made of cement, either white or Portland cement – gray -. Then add pigment to give it a color and zinc to enhance it strengths. So if you want cement color grout add zinc to Portland grout and use it as tile grout. Use black pigment to make darker grey if you like.